PMT Powder Maker Group

Enhance Energy Utilization

Up to 30 % Less Specific Energy

The thermal energy coming from the compression has to be dissipated by cooling down the air for most applications. Together with the well-respected compressor manufacturer KAESER we have developed a machine, which on one the hand generates hot air and on the other hand maximizes the remaining thermal energy of the compressed air by reduced intermediate cooling.

By using specially designed nozzles this part of the energy can be brought together with the energy coming directly from the pressure, in order to achieve even higher velocities of the airstream. This leads to a significant improvement of the energy utilization.

By means of a controlled water injection, the residual thermal energy can be further used while the total system is cooled down before the internal classifying step with the Rotor-Motor-Unit. This leads to improved classifying conditions.

Integrated Rotor-Motor-Unit

Highest Fineness through Circumferential Speed up to 190 m/s

This combined unit, built with the highest precision grants a high operating security and low energy consumption for PMT’s Spiral Jetmill and Ultrafine Classifier. The results from aerodynamic research work were implemented into a patented rotor wheel geometry and in a mechanical concept to achieve circumferential speeds of up to 190 m/s.

When used in jetmills with internal fine grinding and classifying circuit, products with a fineness even below 1 µm can be produced. This fineness can be achieved even in industrial scale machines and high content recovery classifiers.

The rotor unit is directly combined with a high speed motor unit with the advantage of maintenance-free high-speed bearings.

The first Positive Pressure Classifier for the submicron range leads to high classifying efficiency even in the finest cut-point range. The operation under positive pressure leads to optimized dispersion of the feed material based on high shear forces. Separating the particles is the basis for high effiicient classifying results.

Strong agglomerates based on strong surface forces lead to low content recovery in classifying systems. With this the efficiency of the classifier looking at the fines recovery is rather poor. PMT-Jetmill has developed its patented Classifier JS Series which operates under positive pressure with high shear forces.

Based on this special operation these classifiers have the finest range of products in high content recovery. This can also be achieved on an industrial scale.

The use of the Rotor-Motor-Unit enables final product cut-points in the low micrometer and even submicron range.

The optimization of the content recovery over the whole range of finenesses can be achieved by automatic variation of the coarse reject outlet based on a constant internal material load.

https://www.powder-maker.com/en/feinstsichter/

The spiral type Jetmill of PMT-Jetmill is specialized in optimizing air streams to improve efficiencies and to minimize energy consumption for ultra-fine dry grinding.

The integrated dynamic classifier, the so-called Rotor-Motor-Unit is based on its high strength aluminum disks capable to run at a maximum circumferential speed of 190 m/s. This allows products with a fineness in the low micrometer range and depending on the material even below 1 µm.

The fineness can be easily adjusted by variation of the classifier speed.

The specially developed feed control system together with the optimized grinding nozzles lead to high efficiency of the used energy.

In combination with the newly developed EEU System “Enhanced Energy Utilization” we are able to achieve a reduction in energy use of up to 30 % compared to other micronizing systems.

We either use compressed air (3.5 to 15 bar and 240°C) or superheated steam (up to 24 bar and 400°C) as a grinding medium.

With the continuous reject unit unwanted and hard grindable impurities such as Quartz can be removed from the process and enhance the product quality significantly.

https://www.powder-maker.com/en/strahlmuehle/

Toll grinding and toll classifying at the finest end of powder grinding is the speciality of PMT Powder Processing.

We offer toll services for a variety of industrial materials (talc, mica, kaoline, zeolithe,…) as well as for other materials. These are produced upon client request in the range of several kilograms all the way up to hundreds of tons.

Our services

• Fine grinding with Spiral Jetmills
• Fine classifying under overpressure
• Quick and clean product changes
• Packaging on demand
• Storage and transport logistics
• Confident partner during development of new products
• Reliable partner in setting up new new production and supply chains
• Optimized selection of grinding unit
• Quality Management System according to ISO 9001 and ISO 14001

Your benifits

• Extension of product range
• Bridge production bottlenecks
• Highest product quality
• Exact overview of costs
• No investment costs
• No operating costs
• Calculable market launch
• High flexibility

All our grinding units have been adapted to enable exact cleaning of the parts in direct contact with the material, this starts in the feeding area and continues all the way to the packaging nozzle.

Appropriate equipment for the handling of bulk material like valve packaging machines, big bag-filling stations, pallet press, wrapping machine and good storage facilities, completes PMT’s broad customer service.

Our spiral jetmills offer fine grinding with reproducible quality at the highest level!

https://www.powder-maker.com/en/lohnmahlung-lohnsichtung/